Features:                                               * Supports 9.95Gb/s to 11.3Gb/s bit rates * Hot-pluggable SFP+ footprint *  Single LC for Bi-directional Transmission *  Maximum link length of 60km *  Built-in 1270/1330 WDM Filter *  Uncooled 1270nm or 1330nm CWDM DFB Laser. * Power dissipation <1.5W *  No Reference Clock required * Built-in digital diagnostic functions *  Temperature range 0°C to 70°C *  Very low EMI and excellent ESD protection * RoHS Compliant Part   Applications: *  10GBASE-LR/LW Ethernet *  SONET OC-192 / SDH *  10G Fibre Channel   Description:    JHA5960D-2733 & JHA5960D-3327 Bi-directional 10Gb/s (SFP+) transceivers are compliant with the current SFP+ Multi-Source Agreement (MSA) Specification. They comply with 10GBASE-LR/LW Ethernet, SONET OC-192 / SDH and 10G Fibre Channel 1200-SM-LL-L. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the SFP+ MSA.  l Absolute Maximum Ratings   Parameter Symbol Min. Typical Max. Unit Storage Temperature TS -40   +85 °C Supply Voltage VCCT, R -0.5   4 V Relative Humidity RH 0   85 %   l Recommended Operating Environment Parameter Symbol Min. Typical Max. Unit Case operating Temperature TC -5   +70 °C Supply Voltage VCCT, R +3.135   +3.465 V Supply Current ICC     450 mA Power Dissipation PD     1.5 W   l Electrical Characteristics (TOP = 0 to 70 °C, VCC = 3.135 to 3.465 Volts) Parameter Symbol Min Typ Max Unit Note Transmitter: Differential input voltage swing   180   700 mVpp 1 Transmit Disable Input H VIH 2.0   Vcc+0.3 V   L VIL 0   0.8 V   Transmit Enable Output H VOH 2.4   Vcc+0.3 V   L VOL 0   0.4 V 2 Input Differential Impedance Zin 80 100 120 Ω   Receiver Differential output voltage swing   300   850 mVpp 3 LOS Output H VOH 2.4   Vcc+0.3 V 2 L VOL 0   0.4 V   Output Differential Impedance Zon 80 100 120 Ω   Notes: Note 1) TD+/- are internally AC coupled with 100Ω differential termination inside the module. Note 2) Tx Fault and Rx LOS are open collector outputs, which should be pulled up with 4.7k to 10kΩ resistors on the host board. Pull up voltage between 2.0V and Vcc+0.3V. Note 3) RD+/- outputs are internally AC coupled, and should be terminated with 100Ω (differential) at the user SERDES. l Optical Parameters(TOP = 0 to 70°C, VCC = 3.135 to 3.465 Volts) Parameter Symbol Min Typ Max Unit Ref. Transmitter Bit Rate BR 9.9   11.3 Gb/s   Optical Wavelength JHA5960D-2733 λ 1260 1270 1280 nm   JHA5960D-3327   1320 1330 1340   Average output power Po +1   +5 dBm   Optical Extinction Ratio ER 3.5     dB   Spectral width Δλ     1 nm   Side Mode Suppression Ratio SMSR 30     dB   Optical Eye Mask   Compliant with IEEE802.3ae   Receiver Bit Rate BR 9.9   11.3 Gb/s   Optical Wavelength JHA5960D-2733 λ 1320 1330 1340 nm   JHA5960D-3327   1260 1270 1280     Receiver Sensitivity Sen     -22 dBm 1 Maximum Input Power PMAX -7     dBm   LOS De-Assert LOSD     -23 dBm   LOS Assert LOSA -33     dBm   LOS Hysteresis LOSH 0.5   4 dB   Notes: Note 1) Measured with a PRBS of 231-1 at 1 x 10-12 BER and 3.5 dB extinction ratio. l Pin Function Definitions   PIN # Name Function Notes 1 VeeT Module transmitter ground 1 2 Tx Fault Module transmitter fault 2 3 Tx Disable Transmitter Disable; Turns off transmitter laser output 3 4 SDL 2 wire serial interface data input/output (SDA)   5 SCL 2 wire serial interface clock input (SCL)   6 MOD-ABS Module Absent, connect to VeeR or VeeT in the module 2 7 RS0 Rate select0, optionally control SFP+ receiver. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s   8 LOS Receiver Loss of Signal Indication 4 9 RS1 Rate select0, optionally control SFP+ transmitter. When high, input data rate >4.5Gb/s; when low, input data rate <=4.5Gb/s   10 VeeR Module receiver ground 1 11 VeeR Module receiver ground 1 12 RD- Receiver inverted data out put   13 RD+ Receiver non-inverted data out put   14 VeeR Module receiver ground 1 15 VccR Module receiver 3.3V supply   16 VccT Module transmitter 3.3V supply   17 VeeT Module transmitter ground 1 18 TD+ Transmitter inverted data out put   19 TD- Transmitter non-inverted data out put   20 VeeT Module transmitter ground 1   Note 1) The module ground pins shall be isolated from the module case. Note 2) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board. Note 3) This pin shall be pulled up with 4.7K-10Kohms to VccT in the module. Note 4) This pin is an open collector/drain output pin and shall be pulled up with 4.7K-10Kohms to Host_Vcc on the host board. l SFP Module EEPROM Information and Management The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C interface at address A0h and A2h. The memory is mapped in Table 1. Detailed ID information (A0h) is listed in Table 2. And the DDM specification at address A2h. For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.   Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions) Table 2 - EEPROM Serial ID Memory Contents (A0h) Data Address Length (Byte) Name of Length Description and Contents Base ID Fields 0 1 Identifier Type of Serial transceiver (03h=SFP) 1 1 Reserved Extended identifier of type serial transceiver (04h) 2 1 Connector Code of optical connector type (07=LC) 3-10 8 Transceiver 10G Base-LR 11 1 Encoding 64B/66B 12 1 BR, Nominal Nominal baud rate, unit of 100Mbps 13-14 2 Reserved (0000h) 15 1 Length(9um) Link length supported for 9/125um fiber, units of 100m 16 1 Length(50um) Link length supported for 50/125um fiber, units of 10m 17 1 Length(62.5um) Link length supported for 62.5/125um fiber, units of 10m 18 1 Length(Copper) Link length supported for copper, units of meters 19 1 Reserved   20-35 16 Vendor Name SFP vendor name: JHA 36 1 Reserved   37-39 3 Vendor OUI SFP transceiver vendor OUI ID 40-55 16 Vendor PN Part Number: “JHA5960D-2733” or “JHA5960D-3327” (ASCII) 56-59 4 Vendor rev Revision level for part number 60-62 3 Reserved   63 1 CCID Least significant byte of sum of data in address 0-62 Extended ID Fields 64-65 2 Option Indicates which optical SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported) 66 1 BR, max Upper bit rate margin, units of % 67 1 BR, min Lower bit rate margin, units of % 68-83 16 Vendor SN Serial number (ASCII) 84-91 8 Date code JHA’s Manufacturing date code 92-94 3 Reserved   95 1 CCEX Check code for the extended ID Fields (addresses 64 to 94) Vendor Specific ID Fields 96-127 32 Readable JHA specific date, read only 128-255 128 Reserved Reserved for SFF-8079   l Digital Diagnostic Monitor Characteristics Data Address Parameter Accuracy Unit 96-97 Transceiver Internal Temperature ±3.0 °C 98-99 VCC3 Internal Supply Voltage ±3.0 % 100-101 Laser Bias Current ±10 % 102-103 Tx Output Power ±3.0 dB 104-105 Rx Input Power ±3.0 dB   l Regulatory Compliance The JHA5960D-2733 /3327 complies with international Electromagnetic Compatibility (EMC) and international safety requirements and standards (see details in Table following). Electrostatic Discharge (ESD) to the Electrical Pins MIL-STD-883E Method 3015.7 Class 1(>1000 V) Electrostatic Discharge (ESD) to the Single LC Receptacle IEC 61000-4-2 GR-1089-CORE Compatible with standards Electromagnetic Interference (EMI) FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B Compatible with standards Laser Eye Safety FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 Compatible with Class 1 laser product.   l Recommended Circuit Recommended Host Board Power Supply Circuit    Recommended High-speed Interface Circuit l Mechanical Dimensions