Big Discount China Supply High Speed SFP Price 1.25GB/S Optical Transceiver - 10/100/1000BASE-T Copper SFP Transceiver JHA3401 - JHA

Request a Quote

PRODUCTS DETAILS

Features:                                               ♦ Up to 1.25Gb/s bi-directional data links ♦ Hot-pluggable SFP footprint ♦ Extended case temperature range (-40°C to +85°C ) ♦ Fully metallic enclosure for low EMI ♦ Low power dissipation ♦ Compact RJ-45 connector assembly ♦ Detailed product information in EEPROM ♦ +3.3V single power supply ♦ Access to physical layer IC via 2-wire serial bus ♦ 10/100/1000 BASE-T operation in host systems with SGMII interface ♦ Compliant with SFP MSA ♦ Compliant with IEEE Std 802.3TM-2002 ♦ Compliant with FCC 47 CFR Part 15, Class B ♦ RoHS Compliant Products Applications: ♦ 1.25 Gigabit Ethernet over Cat 5 cable ♦ Switch/Router to Switch/Router Link ♦ High speed I/O for file severs Description: JHA3401 10/100/1000BASE-T copper SFP transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and 10/100/1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 10/100/1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The JHA3401 supports 10/100/1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modula-tion (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The JHA3401 provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2-wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2-wire serial bus at address ACh. • SFP to Host Connector Pin Out Pin Signal name Description MSA Notes 1 VEET Transmitter ground (common with receiver ground)   2 TFAULT Transmitter Fault. Not supported Note 1 3 TDIS Transmitter Disable. PHY disabled on high or open Note 2 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. Note 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. Note 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module. Note 3 7 Rate Select No connection required   8 LOS Loss of Signal - High Indicates Loss of Signal Note 4 9 VEER Receiver Ground (common with transmitter ground)   10 VEER Receiver Ground (common with transmitter ground)   11 VEER Receiver Ground(common with transmitter ground)   12 RD- Receiver Inverted DATA out. AC Coupled Note 5 13 RD+ Receiver Non-inverted DATA out. AC Coupled Note 5 14 VEER Receiver Ground (common with transmitter ground)   15 VCCR Receiver Power Supply Note 6 16 VCCT Transmitter Power Supply Note 6 17 VEET Transmitter Ground (Common with Receiver Ground)   18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. Note 7 19 TD- Transmitter Inverted DATA in. AC Coupled. Note 7 20 VEET Transmitter Ground(common with receiver ground)   Notes: 1. TX Fault is not used and is always tied to ground through a 100 ohm resistor. 2. TX Disable as described in the MSA is not applicable to the 1000BASE-T module, but is used for convenience as an input to reset the internal ASIC. This pin is pulled up within the module with a 4.7 KW resistor. Low (0 – 0.8 V): Transceiver on Between (0.8 V and 2.0 V): Undefined High (2.0 – 3.465 V): Transceiver in reset state Open: Transceiver in reset state 3. Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7-10 KW resistor on the host board to a supply less than VCCT + 0.3 V or VCCR + 0.3 V. Mod Def 0 is tied to ground through a 100 ohm resistor to indicate that the module is present. Mod-Def 1 is clock line of two wire serial interface for optional serial ID Mod-Def 2 is data line of two wire serial interface for optional serial ID 4. LVTTL compatible with a maximum voltage of 2.5V. Not supported on HTSFP-24-111X 5. RD-/+: These are the differential receiver outputs. They are ac coupled 100 ohm differential lines which should be terminated with 100 ohm differential at the user SerDes. The ac coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated. These levels are compatible with CML and LVPECL voltage swings. 6. VCCR and VCCT are the receiver and transmitter power supplies. They are defined as 3.3 V ± 5% at the SFP connector pin. The maximum supply current is about 300mA and the associated in-rush current will typically be no more than 30 mA above steady state after 500 nanoseconds. 7. TD-/+: These are the differential transmitter inputs. They are ac coupled differential lines with 100 W differential termination inside the module. The ac coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 –1200 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single ended) be used for best EMI performance. These levels are compatible with CML and LVPECL voltage swings. Diagram of host board connector block pin numbers and names • +3.3V Volt Electrical Power Interface The JHA3401 has an input voltage range of 3.3 V +/- 5%. The 4 V maximum voltage is not allowed for continuous operation. Parameter Symbol Min. Typical Max. Units Notes/Conditions Supply Current Is   320 375 mA 1.2W max power over full range of voltage and temperature. See caution note below Input Voltage Vcc 3.13 3.3 3.47 V Referenced to GND Surge Current Isurge   30   mA Hot plug above steady state current. See caution note Caution: Power consumption and surge current are higher than the specified values in the SFP MSA • Low-Speed Signals MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_ DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. Parameter Symbol Min. Max. Units Notes/Conditions SFP Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc. SFP Output HIGH VOH host_Vcc -0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc. SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc. SFP Input HIGH   2 Vcc + 0.3 V V 4.7k to 10k pull-up to Vcc.   • High-Speed Electrical Interface All high-speed signals are AC-coupled internally. Transmission Line-SFP Parameter Symbol Min. Typical Max. Units Notes/Conditions Line Frequency fL   125   MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX   100   Ohm Differential Rx Input Impedance Zin,RX   100   Ohm Differential   Host-SFP Parameter Symbol Min. Typical Max. Units Notes/Conditions Single ended data input swing Vinsing 250   1200 mV Single ended Single ended data output swing Voutsing 350 100 800 mV Single ended Rise/Fall Time Tr,Tf   175   psec 20%-80% Tx Input Impedance Zin   50   Ohm Single ended Rx Output Impedance Zout   50   Ohm Single ended  • General Specifications Parameter Symbol Min. Typical Max. Units Notes/Conditions Data Rate BR 100   1,000 Mb/s IEEE 802.3 compatible. Cable Length L     100 m Category 5 UTP. BER <10-12   • Environmental Specifications The JHA3401 has an extended range from 0°C to +85°C case temperature as specified in Table 7. Parameter Symbol Min. Typical Max. Units Notes/Conditions Operating Temperature Top 0   85 °C Case temperature Storage Temperature Tsto -40   100 °C Ambient temperature   • Serial ID Memory Contents Data Address Length (Byte) Name of Length Description and Contents Base ID Fields 0 1 Identifier Type of Serial transceiver (03h=SFP) 1 1 Reserved Extended identifier of type serial transceiver (04h) 2 1 Connector Code of optical connector type (22=RJ45) 3-10 8 Transceiver 1000BASE-T 11 1 Encoding 8B10B (01h) 12 1 BR,Nominal Nominal baud rate, unit of 100Mbps 13 1 Reserved (0000h) 14 1 Length(9um,km) Link length supported for 9/125um fiber, units of km 15 1 Length(9um) Link length supported for 9/125um fiber, units of 100m 16 1 Length(50um) Link length supported for 50/125um fiber, units of 10m 17 1 Length(62.5um) Link length supported for 62.5/125um fiber, units of 10m 18 1 Length(Copper) Link length supported for copper, units of meters 19 1 Reserved   20-35 16 Vendor Name SFP vendor name:JHA Technology Co., Ltd 36 1 Reserved   37-39 3 Vendor OUI SFP transceiver vendor OUI ID 40-55 16 Vendor PN Part Number: “JHA3401” (ASCII) 56-59 4 Vendor rev Revision level for part number 60-61 2 Wavelength Laser wavelength 62 1 Reserved   63 1 CCID Least significant byte of sum of data in address 0-62 Extended ID Fields 64-65 2 Option Indicates which optical SFP signals are implemented (001Ah = LOS, TX_FAULT, TX_DISABLE all supported) 66 1 BR, max Upper bit rate margin, units of % 67 1 BR, min Lower bit rate margin, units of % 68-83 16 Vendor SN Serial number (ASCII) 84-91 8 Date code Manufacturing date code 92-94 3 Reserved   95 1 CCEX Check code for the extended ID Fields (addresses 64 to 94) Vendor Specific ID Fields 96-127 32 Readable Vendor specific date, read only • Mechanical Dimensions Mechanical Dimensions of Transceiver JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information. Published by Shenzhen JHA Technology Co., Ltd Copyright © Shenzhen JHA Technology Co., Ltd All Rights Reserved

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours

Leave YourMessage

Thank you! We will reply you via email within 24 hours.

return