Features: ◊ Support 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T ◊ Hot-pluggable SFP footprint ◊ Compact RJ-45 connector assembly ◊ RoHS compliant and lead-free ◊ Single +3.3V power supply ◊ 10 Gigabit Ethernet over Cat 6a cable ◊ Ambient Operating temperature: 0°C to +70°C Applications: ◊ 10G Ethernet over Cat 5 cable ◊ Switch/Router to Switch/Router Link ◊ High speed I/O for file severs Description: JHA3901G SFP+-10GBASE-T Copper Small Form Pluggable (SFP) transceivers are based on the SFP Multi Source Agreement (MSA) . They are compatible with the 10Gbase-T / 5Gbase-T / 2.5Gbase-T / 1000base-T standards as specified in IEEE Std 802.3 . SFP+-10GBASE-T uses the SFP's RX_LOS(must be pulled up on host) pin for link indication. If pull up or open SFP's TX_DISABLE pin, PHY IC be reset. • SFP to Host Connector Pin Out Pin Symbol Name/Description Ref. 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. Not supported. 3 TDIS Transmitter Disable. Laser output disabled on high or open. 2 4 MOD_DEF(2) Module Definition 2. Data line for Serial ID. 3 5 MOD_DEF(1) Module Definition 1. Clock line for Serial ID. 3 6 MOD_DEF(0) Module Definition 0. Grounded within the module. 3 7 Rate Select No connection required 8 LOS High indicates no linked. low indicates linked. 4 9 VEER Receiver Ground (Common with Transmitter Ground) 1 10 VEER Receiver Ground (Common with Transmitter Ground) 1 11 VEER Receiver Ground (Common with Transmitter Ground) 1 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 VEER Receiver Ground (Common with Transmitter Ground) 1 15 VCCR Receiver Power Supply 16 VCCT Transmitter Power Supply 17 VEET Transmitter Ground (Common with Receiver Ground) 1 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 VEET Transmitter Ground (Common with Receiver Ground) 1 Notes: 1. Circuit ground is connected to chassis ground 2. PHY disabled on TDIS > 2.0V or open, enabled on TDIS < 0.8V 3. Should be pulled up with 4.7k - 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. LVTTL compatible with a maximum voltage of 2.5V. Figure 1. Diagram of host board connector block pin numbers and names • Cable Length Standard Cable Reach Host Port 10Gbase-T CAT6A 30m XFI 5Gbase-T/2.5Gbase-t CAT5E 50m 5GBase-R/2.5GBase-X 1000base-T CAT5E 100m 1000base-FX • +3.3V Volt Electrical Power Interface The JHA3901G SFP+-10GBASE-T has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation. +3.3 Volt Electrical Power Interface Parameter Symbol Min Typ Max unit Notes/Conditions Supply Current Is 700 900 mA 3.0W max power over full range of voltage and temperature. See caution note below Input Voltage Vcc 3.13 3.3 3.47 V Referenced to GND Maximum Voltage Vmax 4 V Surge Current Isurge TBD mA Hot plug above steady state current. See caution note below Caution: Power consumption and surge current are higher than the specified values in the SFP MSA • Low-Speed Signals MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals. Both MOD_ DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. Low-Speed Signals, Electronic Characteristics Parameter Symbol Min Max unit Notes/Conditions SFP Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector SFP Output HIGH VOH host_Vcc -0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc,measured at host side of connector SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc,measured at SFP side of connector SFP Input HIGH VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at SFP side of connector • High-Speed Electrical Interface All high-speed signals are AC-coupled internally. High-Speed Electrical Interface, Transmission Line-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz Rx Input Impedance Zin,RX 100 Ohm Differential, for all frequencies between 1MHz and 125MHz High-Speed Electrical Interface, Host-SFP Parameter Symbol Min Typ Max unit Notes/Conditions Single ended data input swing Vinsing 250 1200 mV Single ended Single ended data output swing Voutsing 350 800 mV Single ended Rise/Fall Time Tr,Tf 175 psec 20%-80% Tx Input Impedance Zin 50 Ohm Single ended Rx Output Impedance Zout 50 Ohm Single ended • General Specifications General Parameter Symbol Min Typ Max unit Notes/Conditions Data Rate BR 1 10 Gb/sec IEEE 802.3 compatible. See Notes 1,2 below Notes: Clock tolerance is +/- 50 ppm • Environmental Specifications Automatic crossover detection is enabled. External crossover cable is not required Environmental Specifications Parameter Symbol Min Typ Max unit Notes/Conditions Operating Temperature Top 0 65 °C Case temperature Storage Temperature Tsto -40 85 °C Ambient temperature • Serial Communication Protocol All SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h. Serial Bus Timing, Requirements Parameter Symbol Min Typ Max unit Notes/Conditions I 2C Clock Rate 0 200,000 Hz • EEPROM INFORMATION(A2),optional • Recommended Application Circuit • Serial ID Memory Contents Addr Field Size (Bytes) Name of Field HEX Description 0 1 Identifier 03 SFP 1 1 Ext. Identifier 04 MOD4 2 1 Connector 22 RJ45 3-10 8 Transceiver 00 00 00 00 00 00 00 00 Transmitter Code 11 1 Encoding 06 64B66B 12 1 BR, nominal 67 10000M bps 13 1 Reserved 00 14 1 Length (9um)-km 00 15 1 Length (9um) 00 16 1 Length (50um) 00 17 1 Length (62.5um) 00 18 1 Length (copper) 1E 30m 19 1 Reserved 00 20-35 16 Vendor name JHA Technology Co., Ltd 36 1 Reserved 00 37-39 3 Vendor OUI 00 00 00 40-55 16 Vendor PN JHA3901G ASC II 56-59 4 Vendor rev 31 2E 30 20 V1.0 60-61 2 Wavelength 00 00 850nm 62 1 Reserved 00 63 1 CC BASE XX Check sum of byte 0~62 64-65 2 Options 00 1A LOS, TX_DISABLE, TX_FAULT 66 1 BR, max 00 67 1 BR, min 00 68-83 16 Vendor SN Unspecified 84-91 8 Vendor date code XX XX XX 20 Year, Month, Day 92-94 3 Reserved 00 95 1 CC_EXT XX Check sum of byte 64~94 96-255 160 Vendor specific • Mechanical Dimensions Mechanical Dimensions of Transceiver JHA reserves the right to make changes to the products or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such products or information. Published by Shenzhen JHA Technology Co., Ltd Copyright © Shenzhen JHA Technology Co., Ltd All Rights Reserved